压强对钙钛矿薄膜形貌和结晶性影响的研究

doi:10.7517/j.issn.1674-0475.2017.04.035

影像科学与光化学 ›› 2017, Vol. 35 ›› Issue (5): 749-757.DOI: 10.7517/j.issn.1674-0475.2017.04.035

压强对钙钛矿薄膜形貌和结晶性影响的研究

孔祥彬^1,2, 陈永振^1,2, 李志毅^1,2, 刘彦伟³, 魏晓芳^1,2, 刘建君^1,2, 王瑞芳^1,2, 王鹰^1,2

1. 中国科学院理化技术研究所光化学转换功能材料重点实验室, 北京 100190;
2. 中国科学院大学未来技术学院, 北京 100049;
3. 中国科学院大学化学与化工学院, 北京 100049

收稿日期:2017-01-18 修回日期:2017-03-03 出版日期:2017-09-15 发布日期:2017-09-15
通讯作者: 王鹰
基金资助:
国家自然科学基金（61420106002，51373189）、中国科学院百人计划和国家重点研究发展项目（2016YFB0401004）资助

Effect of Pressure on Morphology and Crystallinity of the Perovskite Thin Film

KONG Xiangbin^1,2, CHEN Yongzhen^1,2, LI Zhiyi^1,2, LIU Yanwei³, WEI Xiaofang^1,2, LIU Jianjun^1,2, WANG Ruifang^1,2, WANG Ying^1,2

1. Key Laboratory of Photochemical Conversion and Optoelectronic Materials, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190, P. R. China;
2. School of Future Technology, University of Chinese Academy of Sciences, Beijing 100049, P. R. China;
3. School of Chemistry and Chemical Engineering, University of Chinese Academy of Sciences, Beijing 100049, P. R. China

Received:2017-01-18 Revised:2017-03-03 Online:2017-09-15 Published:2017-09-15

摘要/Abstract

摘要：

采用新型简便的方法控制钙钛矿层薄膜的结晶过程，对优化制备工艺、获得高性能器件至关重要。本文采用调节真空度的方法有效控制钙钛矿层结晶，系统地研究了压强的作用及其对晶体生长、薄膜形成及器件性能的影响。采用扫描电子显微镜（SEM）、紫外-可见吸收光谱、X射线衍射光谱（XRD）谱图等手段对钙钛矿层的形貌及结晶程度进行了分析表征。在此基础上，制备出器件结构为Glass/ITO/PEDOT：PSS/CH₃NH₃PbI₃/PCBM/Al的钙钛矿太阳能电池，考察了不同压强下的器件性能。结果表明：随压强降低，钙钛矿层结晶程度明显提高，孔洞减少，表面覆盖率提高。同时，器件的短路电流、填充因子以及光电转化效率均随压强降低而提高，器件效率由原来的10.38%提高到12.36%，提高了19%。

关键词: 调节真空度, 压强, 孔洞, 钙钛矿太阳能电池

Abstract:

A novel and simple method to control the crystallization process during the formation of perovskite thin films is critical for optimizing the device fabrication process and constructing high efficiency perovskite solar cells. In this article, a method of adjusting the vacuum was used to effectively control the crystallization process. Furthermore, the role of pressure and its influence upon perovskite crystal growth, film formation and device performance were systematically investigated. The crystallinity and morphology of the perovskite thin film were characterized by scanning electron microscope (SEM), ultraviolet-visible absorption spectra (UV-Vis) and X-ray diffraction (XRD). Based on the structure of Glass/ITO/PEDOT:PSS/CH₃NH₃PbI₃/PCBM/Al, the performance of the device corresponding to the different pressure was studied. The results indicate that the decreased pressure can enhance the crystallinity of the perovskite film obviously, and improve the surface coverage by reducing the amount of holes. At the same time, the short circuit current, filling factor and photoelectric conversion efficiency of the device are all improved with the pressure decreasing. A 19% higher power conversion efficiency of 12.36% was achieved in comparison to the device fabricated by traditional method, which exhibited just 10.38% efficiency.

Key words: vacuum tuning, pressure, hole, perovskite solar cells

孔祥彬, 陈永振, 李志毅, 刘彦伟, 魏晓芳, 刘建君, 王瑞芳, 王鹰. 压强对钙钛矿薄膜形貌和结晶性影响的研究[J]. 影像科学与光化学, 2017, 35(5): 749-757.

KONG Xiangbin, CHEN Yongzhen, LI Zhiyi, LIU Yanwei, WEI Xiaofang, LIU Jianjun, WANG Ruifang, WANG Ying. Effect of Pressure on Morphology and Crystallinity of the Perovskite Thin Film[J]. Imaging Science and Photochemistry, 2017, 35(5): 749-757.

参考文献

[1] Grätzel M. Dye-sensitized solar cells[J]. Journal of Photochemistry & Photobiology C:Photochemistry Reviews, 2003, 4(2):145-153.
[2] 吴世康, 汪鹏飞. 功能染料在有机太阳能电池中的应用[J]. 影像科学与光化学, 2010, 28(3):217-229. Wu S K, Wang P F. The application of functional dyes in solar cell[J]. Imaging Science and Photochemistry, 2010, 28(3):217-229.
[3] 李胜军, 林原, 杨世伟, 陈今茂, 肖绪瑞. 染料敏化太阳能电池TiO₂电极的制备及电解质的影响[J]. 影像科学与光化学, 2008, 26(1):54-59. Li S J, Lin Y, Yang S W, Chen J M, Xiao X R. Preparation of TiO₂ electrode for dye-sensitized solar cell and the effect of electrolyte[J]. Imaging Science and Photochemistry, 2008, 26(1):54-59.
[4] Xing G C, Mathews N, Sun S Y, Lim S S, Lam Y M, Grätzel M, Mhaisalkar S, Sum T C. Long-range balanced electron-and hole-transport lengths in organic-inorganic CH₃NH₃PbI₃[J]. Science, 2013, 342(6156):344-347.
[5] De Wolf S, Holovsky J, Moon S J, Löper P, Niesen B, Ledinsky M, Haug F J, Yum J H, Ballif C. Organometallic halide perovskites:sharp optical absorption edge and its relation to photovoltaic performance[J]. Journal of Physical Chemistry Letters, 2014, 5(6):1035-1039.
[6] Noh J H, Im S H, Heo J H, Mandal T N, Seok S I. Chemi-cal management for colorful, efficient, and stable inorganic-organic hybrid nanostructured solar cells[J]. Nano Letters, 2013, 13(4):1764-1769.
[7] Kojima A, Teshima K, Shirai Y, Miyasaka T. Organometal halide perovskites as visible-light sensitizers for photovoltaic cells[J]. Journal of the American Chemical Society, 2009, 131(17):6050-6051.
[8] Jung H S, Park N G. Perovskite solar cells:from materials to devices[J]. Small, 2015, 11(1):10-25.
[9] Nie W Y, Tsai H, Asadpour R, Blancon J C, Neukirch A J, Gupta G, Crochet J J, Chhowalla M, Tretiak S, Alam M A. High-efficiency solution-processed perovskite solar cells with millimeter-scale grains[J]. Science, 2015, 347(6221):522-525.
[10] Zhao Y C, Wei J, Li H, Yan Y, Zhou W K, Yu D P, Zhao Q. A polymer scaffold for self-healing perovskite solar cells[J]. Nature Communications, 2016, 7:10228.
[11] Xiao Z G, Dong Q F, Bi C, Shao Y C, Yuan Y B, Huang J S. Solvent annealing of perovskite-induced crystal growth for photovoltaic-device efficiency enhancement[J]. Advanced Materials, 2014, 26(37):6503-6509.
[12] Jeon N J, Noh J H, Kim Y C, Yang W S, Ryu S, Seok S I. Solvent engineering for high-performance inorganic-organic hybrid perovskite solar cells[J]. Nature Materials, 2014, 13(9):897-903.
[13] Bi C, Wang Q, Shao Y C, Yuan Y B, Xiao Z G, Huang J S. Non-wetting surface-driven high-aspect-ratio crystalline grain growth for efficient hybrid perovskite solar cells[J]. Nature Communications, 2015, 6:7747.
[14] Seo J, Park S, Kim Y C, Jeon N J, Noh J H, Yoon S C, Seok S I. Benefits of very thin PCBM and LiF layers for solution-processed p-i-n perovskite solar cells[J]. Energy & Environmental Science, 2014, 7(8):2642-2646.
[15] Li X, Dar M I, Yi C Y, Luo J S, Tschumi M, Zakeeruddin S M, Nazeeruddin M K, Han H W, Grätzel M. Improved performance and stability of perovskite solar cells by crystal crosslinking with alkylphosphonic acid ω-ammonium chlorides[J]. Nature Chemistry, 2015, 7(9):703-711.
[16] Liang P W, Liao C Y, Chueh C C, Zuo F, Williams S T, Xin X K, Lin J J, Jen A K Y. Additive enhanced crystallization of solution-processed perovskite for highly efficient planar-heterojunction solar cells[J]. Advanced Materials, 2014, 26(22):3748-3754.
[17] Burschka J, Pellet N, Moon S J, Humphry-Baker R, Gao P, Nazeeruddin M K, Grätzel M. Sequential deposition as a route to high-performance perovskite-sensitized solar cells[J]. Nature, 2013, 499(7458):316-319.
[18] Cheng N, Liu P, Bai S H, Yu Z H, Liu W, Guo S S, Zhao X Z. Enhanced performance in hole transport material free perovskite solar cells via morphology control of PbI₂ film by solvent treatment[J]. Journal of Power Sources, 2016, 319:111-115.
[19] Du T, Wang N, Chen H J, Lin H, He H C. Comparative study of vapor-and solution-crystallized perovskite for planar heterojunction solar cells[J]. ACS Applied Materials & Interfaces, 2015, 7(5):3382-3388.
[20] Ke W J, Fang G J, Wan J W, Tao H, Liu Q, Xiong L B, Qin P L, Wang J, Lei H W, Yang G, Qin M C, Zhao X Z, Yan Y F. Efficient hole-blocking layer-free planar halide perovskite thin-film solar cells[J]. Nature Communications, 2015, 6:6700.
[21] Zhou Y Y, Yang M J, Pang S P, Zhu K, Padture N P. Exceptional morphology-preserving evolution of formamidinium lead triiodide perovskite thin films via organic-cation displacement[J]. Journal of the American Chemical Society, 2016, 138(17):5535-5538.
[22] Guo Q, Li C, Qiao W Y, Ma S, Wang F Z, Zhang B, Hu L H, Dai S Y, Tan Z A. The growth of a CH₃NH₃PbI₃ thin film using simplified close space sublimation for efficient and large dimensional perovskite solar cells[J].Energy & Environmental Science, 2016, 9(4):1486-1494.
[23] Li X, Bi D Q, Yi C Y, Décoppet J D, Luo J S, Zakeeruddin S M, Hagfeldt A, Grätzel M. A vacuum flash-assisted solution process for high-efficiency large-area perovskite solar cells[J]. Science, 2016, 353(6294):58-62.
[24] Eperon G E, Burlakov V M, Docampo P, Goriely A, Snaith H J. Morphological control for high performance, solution-processed planar heterojunction perovskite solar cells[J]. Advanced Functional Materials, 2014, 24(1):151-157.
[25] Tripathi N, Shirai Y, Yanagida M, Karen A, Miyano K. Novel surface passivation technique for low-temperature solution-processed perovskite PV cells[J]. ACS Applied Materials & Interfaces, 2016, 8(7):4644-4650.
[26] Wharf I, Gramstad T, Makhija R, Onyszchuk M. Synthesis and vibrational spectra of some lead (Ⅱ) halide adducts with O-, S-, and N-donor atom ligands[J]. Canadian Journal of Chemistry, 1976, 54(21):3430-3438.
[27] Ahn N, Son D Y, Jang I H, Kang S M, Choi M, Park N G. Highly reproducible perovskite solar cells with average efficiency of 18.3% and best efficiency of 19.7% fabricated via Lewis base adduct of Lead (Ⅱ) iodide[J]. Journal of the American Chemical Society, 2015, 137(27):8696-8699.
[28] Xie F X, Zhang D, Su H M, Ren X G, Wong K S, Grätzel M, Choy W C H. Vacuum-assisted thermal annealing of CH₃NH₃PbI₃ for highly stable and efficient perovskite solar cells[J]. ACS Nano, 2015, 9(1):639-646.

压强对钙钛矿薄膜形貌和结晶性影响的研究

Effect of Pressure on Morphology and Crystallinity of the Perovskite Thin Film

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 1

编辑推荐

Metrics

本文评价